AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
2015 honda odyssey belt diagram9/12/2023 ![]() ![]() Misalignment of the cable reel could cause an open in the wiring, making the SRS system, Power sliding door control unit (see RESETTING THE POWER SLIDING DOORĬONTROL UNIT ), and reset the power tailgate control unit (see RESETTING THEīefore returning the vehicle to the customer, enter the radio code, the navigation code, thenĮnter the radio station and XM channel presets set the clock. After reconnecting the battery, reset the Get the customer's anti-theft codes and write down the radio station and XM channel presetsīefore disconnecting the battery negative cable. The original radio and navigation system have a coded theft protection circuit.A tester with a higher output could cause accidental deployment and possible injury.ĭo not put objects on the front passenger's airbag. Its output is 10 mA (0.01 A) or less when switched to the lowest value in the ohmmeter If it is not a Honda multimeter, make sure Use only a digital multimeter to check the system. Of being dropped or improperly handled, such as dents, cracks or deformation.īefore removing any of the SRS parts (including the disconnection of the connectors), Use only new parts when making SRS repairs.Ĭarefully inspect any SRS part before you install it. Use replacement parts which are manufactured to the same standards and quality as the.Turned OFF or the battery cables are disconnected from theįriday, Ap4:06:21 PM © 2005 Mitchell Repair Information Company, LLC. NOTE: The SRS memory is not erased even if the ignition switch is The SCS line with the HDS to take the PCM out of active status, disconnect the negativeĬable from the battery, and wait at least 3 minutes before beginning work. Observe the instructions described in this information, or the airbags could accidentally deployĮxcept when performing electrical inspections, always turn the ignition switch OFF, ground Please read the following precautions carefully before performing the airbag system service. 2: Identifying SRS Components Location (2 Of 2) 1: Identifying SRS Components Location (1 Of 2)Ĭourtesy of AMERICAN HONDA MOTOR CO., INC.Ģ005-06 RESTRAINTS SRS (Supplemental Restraint System) - Odysseyįriday, Ap4:06:20 PM © 2005 Mitchell Repair Information Company, LLC.įriday, Ap4:06:47 PM © 2005 Mitchell Repair Information Company, LLC. SRS (Supplemental Restraint System) - Odysseyįig. Looking for some other Service Repair Manual,please check: NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to have2005 HONDA ODYSSEY Service Repair Workshop Manual. Using this repair manual is an inexpensive way to keep your vehicle working properly.Ĭompatible: All Versions of Windows & Mac ![]() Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.2005 HONDA ODYSSEY Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. Make sure the belt is seated properly on each pulley.This is the Highly Detailed factory service repair manual for the2005 HONDA ODYSSEY, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact.Place the power steering reservoir back into the bracket.Release tension, and remove the wrench.Slide the drive belt over the tensioner pulley. Move the tensioner as you did earlier when you removed the belt.Route the new belt on the power steering pump.Route the new belt underneath the tensioner pulley.Place the new belt over the idler pulley.Route the new belt underneath the crankshaft pulley and the AC compressor.Make sure that the old and new belt has the same length.Keep on applying pressure until the serpentine belt is loose.Apply thrust toward the back and windshield of the vehicle. Or connect the socket and the breaker bar. Use a wrench to release the tensioner.Create a diagram of how the serpentine belt is connected to different pulleys.Pull the hood release under the dashboard and open the hood.Park the vehicle on level ground and set the parking brakes.Tensioner bolt may be 13mm, 14mm or 19mm. ![]()
0 Comments
Read More
Leave a Reply. |